For volumetric concrete mixer operations, low-profile ("pig") trailer silos are the industry standard because they tow behind a 1-ton pickup or flatbed, set up without a crane, and keep travel heights under 13'6".
The Mix Right 7SL-80 is the best all-around choice for remote, self-contained job sites due to its hydraulic drive and onboard gas/diesel engine options, while the Fast-Way Silo 210 leads in pure reload speed when 3-phase power is available.
Side-by-Side Comparison of Top Portable Silos
| Model | Storage Capacity | Auger Size | Discharge Rate | Standard & Optional Power | Weight & Towing |
|---|---|---|---|---|---|
| Mix Right 7SL-80 | 35 Tons (200 bbl) | 6" standard
8" optional | 900 lbs/min (6")
1,500 lbs/min (8") | 14 HP Kohler Gas (standard)
23.5 HP Gas (for 8" auger), Diesel, 480V 3-Phase Electric, or Hybrid Gas/Electric | 8,000 lbs empty
1-ton pickup towable |
| Mix Right 7SL-120 | 55 Tons (~300 bbl) | 6" standard
8" optional | 900 lbs/min (6")
1,500–2,500 lbs/min (8") | 23.5 HP Gas, Diesel, or 480V 3-Phase Electric | Heavy-duty tandem/triple axle; pintle hitch |
| ProAll 200 LoPro | 37.6 Tons (200 bbl) | 8" standard | ~1,500–1,800 lbs/min | 5 HP 3-Phase Electric bottom drive (standard)
Gas engine hydraulic package optional | 8,000 lbs empty
Dual 6,000-lb axles, electric brakes |
| Fast-Way SI-LOW 208 | ~37.6 Tons (1,400 cu. ft.) | 8" standard | 1,500 lbs/min | Hydraulic or Electric (240/480V 3-Phase) | Dual 8,000-lb axles, pintle hitch |
| Fast-Way Silo 210 | 37.6 Tons (200 bbl / 800 cu. ft.) | 10" tubular | 3,500–3,700 lbs/min | 15 HP 240/480V 3-Phase Electric | 9,220 lbs empty
Pintle hitch required |
| ProAll 350bbl Tip-Up | 65.8 Tons (350 bbl) | 10" forced-feed | 3,000+ lbs/min | 10 HP Electric gearbox drive (standard)
Gas power pack optional | Vertical tip-up (37' tall deployed); Torflex axle, pintle hitch |
How to Choose Based on Your Volumetric Operation
1. Discharge Rate & Reload Turnaround Time
A typical 10-cubic-yard volumetric mixer holds roughly 5,000 to 6,500 lbs of cement powder (at ~550–650 lbs/yd³ for a standard 6-sack mix).
* 6-Inch Auger (~900 lbs/min): Takes 6 to 7 minutes to reload an empty 10-yard mixer. Fine for single-truck operations, but creates a bottleneck if two trucks return simultaneously.
* 8-Inch Auger (~1,500 lbs/min): Cuts reload time to 3.5 to 4.5 minutes. This is the sweet spot for 1-to-3 truck fleets.
* 10-Inch Auger (~3,500 lbs/min): Reloads a 10-yard mixer in under 2 minutes. Best for multi-truck yards or continuous high-volume pours where drivers cannot wait in line.
2. Power Source & Drive Train
* Self-Contained Gas / Diesel (Hydraulic Drive): Essential for remote job sites without grid power. Hydraulic drives (like the Mix Right 7SL series) eliminate mechanical gearboxes and shear pins—if compacted cement stalls the screw, the hydraulic relief valve simply bypasses instead of snapping a drive shaft. Note: Always upgrade to the 20+ HP engine if ordering an 8-inch auger; a 14 HP engine will bog down under full load.
* 240V / 480V 3-Phase Electric (Direct/Gearbox Drive): Lower maintenance, quieter, and delivers higher continuous torque for 10-inch augers. Ideal if the silo stays parked at a yard or batch site with generator/utility hookups.
* Hybrid Dual-Power (Gas + Electric): Offered by Mix Right, allowing you to run off cheap yard electricity at your home base and switch to the onboard Kohler engine on remote sites.
3. Must-Have Options for Volumetric Workflows
* Load-Cell Scale Package: Because volumetric trucks meter cement by auger revolution rather than weight, adding a 4-cell electronic weigh system (such as Fast-Way’s 80,000-lb scale kit or Mix Right’s 920i load cells) lets you verify exact cement inventory and track batch yields per truck.
* Aeration + Vibrator Combo: Low-profile horizontal silos have shallow floor angles compared to vertical silos. Ensure the unit has both pneumatic aeration pads (puffer pads) and a hydraulic/pneumatic vibrator to prevent cement from rat-holing above the auger trough.
* Minimum 35-Ton (200 Barrel) Capacity: Pneumatic bulk cement tankers typically deliver 25 to 28 tons per load. Buying a 15-ton silo forces you to pay split-load delivery fees or leave cement on the tanker; a 35-ton silo accepts a full tanker load with 7 to 10 tons of reserve headroom.
Cement transfers from a portable silo into a volumetric concrete mixer via an enclosed, dust-sealed gravity-to-auger-to-gravity path:
Silo Discharge: The volumetric truck backs under the silo’s pivoted discharge auger. The operator lowers the flexible rubber loading sock (boot) into the truck's top cement bin hatch to create a dust-tight seal.
Fluidization & Auger Transfer: Pneumatic aeration pads and vibrators fluidize the powder in the silo cone, feeding it into the silo’s inclined screw auger. The auger elevates the cement out of the silo and drops it through the sock into the truck’s onboard cement bin.
Dust Displacement: As cement fills the truck's bin, displaced air vents back up through a dust return hose (or integrated double-walled sock) into the silo's pulse-jet dust collector, keeping the transfer dust-free.
Watching the process in action shows how the truck positions under the discharge chute and seals the loading boot: